ASK514280 ml
Sprayable Hybrid Polymer Body Seam Sealer, Beige (Shore A 35)
The sprayable one-component sealant AXIOM® ASK514 based on low-viscosity hybrid polymers is intended for sealing body joints, welded seams and lap joints in transport and industrial mechanical engineering. It is used in the manufacture and repair of passenger cars, trucks and commercial vehicles, including for restoring original factory coatings. It creates a durable anti-corrosion and sound-insulating coating. Effective for sealing hard-to-reach places. It is applied with a gun, brush or spatula.
Ready for use, it requires no priming or preparatory materials before application. It is characterised by excellent adhesion to all materials used in body work, including ferrous and non-ferrous metals, painted surfaces and various types of plastic (except polyethylene, polypropylene and fluoroplastic).
It withstands compression, tension and shear. It reduces vibration and noise and is resistant to loads. Shore A hardness (GOST 263-75) — 60.
Homogeneous, it does not form bubbles and does not shrink. Thixotropic, when applied it does not run and does not slide down the seam. Resistant to ageing, to the effects of temperature fluctuations and adverse weather factors. The MS-polymer (MS polymer) can be painted both over the wet layer and after the surface skin has formed, within 2 hours of application (carry out a trial test before painting). Chemically neutral, it does not react with the materials being sealed, does not cause corrosion of metals and is suitable for application to surfaces made of delicate materials. Odourless, environmentally safe, non-toxic and non-flammable, it contains no isocyanates, solvents or silicones. For interior and exterior work.
- Work is recommended at a temperature between +5°C and +35°C.
- Apply the sealant to clean, degreased surfaces.
- For neat work, use masking tape and remove it immediately after applying the sealant.
- Use a special pneumatic gun for application. Cut off the screw head of the tube above the thread and place the tube into the gun.
- Spray the sealant from a distance of 30‑40 cm.
- To obtain the required coating texture it is recommended to carry out a test spray, adjusting the ratio between the atomising air flow and the sealant fed from the cartridge.
- If necessary, the sealant can be applied with a brush or a spatula, giving the previously applied bead the required shape and texture.
- Full curing takes place under the action of atmospheric moisture within 3‑7 days.
- Skin formation time — at least 20 minutes, sealant curing rate — 3–4 mm per day (at a temperature of +23°C and a relative humidity of 50%).
- Clean surfaces contaminated with freshly applied sealant using a solvent. Remove the cured compound mechanically.
- The finished coating may be used at temperatures between –40°C and +110°C.
Attention! On completion of work, to avoid clogging the spray head, clean it in accordance with the instructions for the pneumatic gun. Do not use on surfaces where contact with food is possible. Not suitable for continuous immersion in water.
| Color | Beige |
|---|---|
| Base | Hybrid |
| Shore A Hardness | 35 (GOST 263‑75) |
| Skin formation time | 20 minutes |
| Equivalents | Teroson 9320, Sikaflex-529 AT, SabatacK 710, BOSTIC 7007 A, 3M 8851 |
| Curing rate | 3-4 mm per day |
| Shelf Life | 12 months |
| Storage | In the hermetically sealed original packaging in a dry place at a temperature from +5°C to +25°C. Freezing down to –20°C for up to 45 days is permitted. |
| Units per Box | 12 pieces |
| Technical Specification | 20.30.22‑001‑01324561‑2019 |
| Composition | hybrid polymer, mineral fillers, functional additives, pigments |
| EAN-13 | 4606445041396 |
евгений – :
Здравствуйте! через какое время можно наносит краску на данный продукт, при окрасе Мокрый по Мокрому? использование на порогах авто
Спасибо
axiom – :
Лучше всего в течение получаса, в течение двух часов тоже хорошо.
Эдуард – :
Здравствуйте. Можно ли красить данный герметик водно-дисперсионной (акриловой) краской из балончика ?
Заранее благодарю за ответ.
axiom – :
Можно
Владимир – :
Здравствуйте. Ваш герметик самый лучший из того, что пробовал ( распыляемые несколько видов от разных производителей) . Не меняйте в нём ничего (цвет/кончистенция)- он оптимален! Краска на нём держится великолепно. Очень подходит под ОЕМ автомобильные швы.
axiom – :
Спасибо! Будем стараться
Алексей – :
Здравствуйте!
Вопрос №1. Краска не держится на данном герметике. Пробовал окрашивать и сразу после нанесения и в течение двух часов. Буквально небольшое механическое воздействие и краска отстает. Как правильно красить данный герметик? Нужно ли применять сначала грунт, например акриловый?
Вопрос №2. Можно ли наносить его на эпоксидный или кислотный грунт?
Спасибо за ответы!
axiom – :
Судя по вашему письму, вы все делаете правильно. Причину дистанционно мы установить не сможем. Для улучшения адгезии можете предварительно загрунтовать герметик либо адгезионным грунтом для пластика, либо эпоксидным грунтом. На эпоксидный грунт герметик наносить можно, это дополнительно улучшает адгезию герметика. На кислотный нельзя.