ABP531600 ml
AXIOM® BOND Fast-Curing Hybrid Polymer Adhesive, White (Shore A 65)
Designed for creating high-strength adhesive seam joints in transport and industrial mechanical engineering. Suitable for joint seams subjected to vibration loads. AXIOM® ABP531 with its high curing rate is used in the manufacture and repair of commercial vehicles for mounting the body elements of buses, trucks and cars and special-purpose vehicles (cash-in-transit vans, ambulances, refrigerated vehicles, and also motorhomes and trailers). Widely used in the assembly of marine transport (elements above the waterline), railway carriages, air conditioning and ventilation systems, etc.
Withstands compression, tension and shear. Reduces vibration and noise, is resistant to loads and is perfectly suited to bonding materials with different thermal expansion. Shore A hardness (GOST 263‑75) — 65.
AXIOM® BOND ABP531 based on hybrid polymers (a modern equivalent of MS polymers) cures quickly: 30 minutes after application the adhesive joint is able to withstand a high load. Ready to use, it requires no priming or preparatory materials before application. Thixotropic, during application it does not run or slump along the seam. It does not shrink and does not form bubbles. Once cured it can be sanded and painted with water-based and synthetic paints (when using solvent-based paints, carry out a trial test). Sufficient for 20–22 linear metres at a bead diameter of 4 mm.
Chemically neutral, it does not react with the materials being bonded, does not cause corrosion of metals and is suitable for bonding items made of delicate materials. Odourless, environmentally safe, non-toxic and non-flammable, it contains no isocyanates, solvents or silicones. Resistant to ageing, temperature fluctuations and adverse weather factors. It has a wide service temperature range: from –65°C to +90°C. For interior and exterior work.
- Withstands compression, tension and shear. Reduces vibration and noise, is resistant to loads and is perfectly suited to bonding materials with different thermal expansion.
- Shore A hardness (GOST 263‑75) — 65.
- Cures quickly: 30 minutes after application the adhesive joint is able to withstand a high load.
- Ready to use, it requires no priming or preparatory materials before application.
- Thixotropic, during application it does not run or slump along the seam. It does not shrink and does not form bubbles.
- Once cured it can be sanded and painted with water-based and synthetic paints (when using solvent-based paints, carry out a trial test). Sufficient for 20–22 linear metres at a bead diameter of 4 mm.
- Chemically neutral, it does not react with the materials being bonded, does not cause corrosion of metals and is suitable for bonding items made of delicate materials.
- Odourless, environmentally safe, non-toxic and non-flammable, it contains no isocyanates, solvents or silicones.
- Resistant to ageing, temperature fluctuations and adverse weather factors.
- It has a wide service temperature range: from –65°C to +90°C.
- Work is recommended at a temperature between +5°C and +35°C.
- Apply the adhesive to clean, degreased surfaces.
- For neat work, use masking tape and remove it immediately after applying the adhesive.
- Cut off the screw head of the tube above the thread, screw on the nozzle, unscrew the cap and cut the nozzle tip so that an opening sufficient for dispensing is formed.
- Apply the adhesive to the elements to be bonded in strips at intervals of 5–15 cm to provide air access. Where the area of the surfaces to be bonded is small, continuous application is permissible. Use a manual or pneumatic gun for application.
- Press the element to be bonded against the mounting point with maximum force and position it precisely. If necessary, provide temporary fixing.
- Clean surfaces contaminated with freshly applied adhesive with a solvent.
- Remove cured adhesive mechanically.
Attention! Do not use on surfaces where contact with food is possible. Not suitable for continuous immersion in water.
| Color | White |
|---|---|
| Base | Hybrid |
| Shore A Hardness | 65 (GOST 263‑75) |
| Skin formation time | 20 minutes |
| Equivalents | Terostat MS 9380, Sikaflex 552, SabatacK 790, TENABOND 341S, SOUDASEAL 270 HS |
| Curing rate | After just 30 minutes the adhesive joint is able to withstand a high load |
| Shelf Life | 12 months |
| Storage | In the hermetically sealed original packaging in a dry place at a temperature from +5°C to +25°C. Freezing down to –20°C for up to 45 days is permitted |
| Composition | hybrid polymer, mineral fillers, functional additives, pigments |
| EAN-13 | 4606445046922 |
There are no questions about this product yet.